Home > Solution

Twin-line centralized lubrication system

Built-in safety valve adopted. No need to consider the sealing of safety valve;

The Twin-line lubrication pump adopts a multi-plunger pair uniformly distributed structure, increasing the grease supply of the Twin-line pump, without increasing the motor load, avoiding emptying the lubrication pump;

The grease channel inside the Twin-line divider is short, which accelerates the flow of grease in the pipeline, thus reducing the possibility of dry junction of grease in the pipeline

The piston of the Twin-line lubrication pump has a more reliable push-pull structure and eliminates the failure of plunger to retreat due to spring fatigue;

Twin-line lubrication pump adopts mechanical power reversing, safe and reliable;

Suitable for low temperature and high viscosity grease and long pumping distance situation, widely used in large equipment such as engineering machinery, wind power generation equipment, mining and metallurgy, and automated production lines.

Get Inquiry

Send Email

Waste lubricating grease collection system

Introduction

The Twin-line centralized lubrication system consists of a lubrication pump, a Twin-line divider , a control unit and pipeline accessories. The lubrication pump alternately supplies grease to the Twin-line divider through two main lines, and the divider quantitatively distributes the grease. A progressive divider can also be connected behind the Twin-line divider to increase the number of lubrication points supplied by the Twin-line system.
The advantage of the Twin-line system is that it can transport and accurately distribute grease over a large distance. A pressure sensor can be installed on the main line to monitor the working status of the entire system.
During the operation of the pump, the Twin-line divider can be alternately supplied with grease through two main lines to meet the lubrication of equipment with large grease demand.

Features And Benefits

01 Hydraulic pump

ADP120 series Twin-line centralized lubrication system is a new generation of centralized lubrication system developed by Autol Technology after long-term market research and technological innovation. During the research and development process, it applied for a number of technical inventions and technological innovation patents. ADP120 series Twin-line lubrication pump is driven by a high-performance DC motor, with a turbine and worm gear reducer inside, and drives 3 pump cores to work at the same time. The built-in relief valve and mechanical reversing valve are used, which not only makes the lubrication pump simple and beautiful in appearance, but also has stable and reliable performance.

02 Twin-line divider

The grease volume of the Twin-line divider is easy to adjust, and more than 10 times of grease volume ratio can be achieved by replacing the quantitative plug;
The short internal grease passage of the Twin-line divider makes units independent from each other without mutual interference;

03 Monitor

The monitor is the control center of the centralized lubrication system. It can dynamically display operating parameters such as system pressure, rest countdown, operation timer, cumulative working times and fault codes, and has functions such as low temperature protection, overload protection, low liquid level alarm and blockage alarm.

Technical Parameters

Piston Pump

Product Picture
Model	ADP120 series	ADPB series	ABDB12 series
Voltage	DC24V/AC230V	DC24V	multi-phase motor : 380-420 VAC/50 Hz; 440-480 VAC /60 Hz; single-phase motor: 500VAC/50Hz
Output Flow	12 ml/min	20 ml/min	K7(0.1ml/cy〜0.36ml/cy) K12(0.29ml/cy〜1.05ml/cy)
Reservior	4L & 8L & 10& 15l & 20L	20L & 40L & 60L	30L
Outlet Number	2 pcs	2 pcs	1-12 pcs
Operating Pressure	20 MPa	35 MPa	35 MPa
Applicable Grease	NLGI-0#,1#,2#	NLGI-0#,1#,2#	oil: viscosity of at least 40 m㎡/s grease: up to NLGl-2
IP Grade	IP65	IP65	IP55
Control Mode	External/Internal Monitor	External Monitor
Operating Temperature	T -40 °C~70°C	T -40 °C~70°C	T -20 °C~70°C

Distributor

Product Picture
Model	ASP series	CSP series
Operating Temperature	-40℃~80℃	-40℃~80℃
Outlet Flow	0.1, 0.15, 0.2,0.4, 0.6, 0.8 & 1 mL/cy	0.1, 0.15, 0.2,0.4, 0.6, 0.8 & 1 mL/cy
Number of Outlets	2-20	2-20
Operating Pressure	25MPa	25MPa
Applicable Grease	NLGI-0#, 1# & 2#	NLGI-0#, 1# & 2#
Inlet/outlet Thread	M10X1	M10X1